| |
|
|
|
|
|
|
| |
|
| |
 |
|
| |
|
|
| |
|
The Journal of Mechanical Science and Technology, Volume 22, Number 8, 2008 |
|
|
A Study on the Heat Treatment Characteristics of Ti-alloys without Al as Biomaterials
Jaesam Ban
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1447-1450, 2008 |
|
|
Structural integrity assessment of reactor pressure vessels during pressurized thermal shock
Myung Jo Jhung
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1451-1459, 2008 |
|
|
Stress in Piezoelectric Hollow Sphere with Thermal Gradient
mahdi saadatfar
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1460-1467, 2008 |
|
|
Soundproof effect of nanoreinforced polymer composites
Yeon-Jun Kang
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1468-1474, 2008 |
|
|
Fuzzy Logic versus a PID Controller for Position Control of a Muscle-like Actuated Arm
C. S. Lee
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1475-1482, 2008 |
|
|
A study on the thermomechanical behavior of semiconductor chips on thin silicon substrate
Seyoung Im
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1483-1489, 2008 |
|
|
Development of a wall-climbing robot using a tracked wheel mechanism
Jongwon Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1490-1498, 2008 |
|
|
IDENTIFICATION OF AIRWAY CHARACTERISTICS USING THE INPUT IMPEDANCE
Seonhwan Cheong
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1499-1503, 2008 |
|
|
Experimental Identification for Inverse Problem of a Mechanical System with a Non-minimum Phase Based on Singular Value Decomposition
Sang Kwon Lee
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1504-1509, 2008 |
|
|
A Method for Planar Development of 3D surfaces in Shoe Pattern Design
Sung-Hwan Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1510-1519, 2008 |
|
|
A Control System for Uniform Bead in Fillet Arc Welding on Tack Welds
Jae-Woong Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1520-1526, 2008 |
|
|
Additive properties of saturated very long chain fatty acids in Castor and Jojoba oils
Hosung Kong
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1527-1536, 2008 |
|
|
Optimum design of roll forming process of slide rail using design of experiments
Naksoo Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1537-1543, 2008 |
|
|
Mathematical modelling and experimental investigation on sun and solar drying of white mulberry
Ebru Akpinar Kavak
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1544-1553, 2008 |
|
|
Study on the Concentration of CO by the Length and the Variation of the Bent tube of the Exhaust pipe for the Household Boiler
Sahwan Leem
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1554-1560, 2008 |
|
|
Investigation of Gas Flow Characteristics in Proton Exchange Membrane Fuel Cell
Honggun Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1561-1567, 2008 |
|
|
Characteristics of the Cooling Water Fouling in a Heat Exchanging System
Sun-Kyung Sung
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1568-1575, 2008 |
|
|
Optimal Design for Hybrid Rocket Engine for Air Launch Vehicle
Changjin Lee
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1576-1585, 2008 |
|
|
Supercritical Droplet Dynamics and Emission in Low Speed Cross-Flows
Woongsup Yoon
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1586-1601, 2008 |
|
|
Study on Operating Characteristics of Fuel Cell Powered Electric Vehicle with Different Air Feeding Systems
Kyoungdoug Min
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1602-1611, 2008 |
|
|
Spectral Element Modeling and Analysis of the Blood Flow through a Human Blood Vessel
Usik Lee
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1612-1619, 2008 |
|
|
PHASE DOPPLER MEASUREMENTS: SYSTEM SET-UP OPTIMIZATION FOR CHARACTERIZATION OF A DIESEL NOZZLE
Raul Payri
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1620-1632, 2008 |
|
|
Geometrical Effects on Spray Characteristics of Air-Pressurized Swirl Flows
Sam Goo Lee
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1633-1639, 2008 |
|
|
Numerical Study on Performance of Supersonic Inlets with Various Three-dimensional Bumps
Sang Dug Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 8, pp.1640-1647, 2008 |
|
|
|
|
 |
|
|
|
|
| |
| |
| |
|
|
| |
|
JMST Editorial Office: #702 KSTC New Bldg, 22 7-gil, Teheran-ro, Gangnam-gu, Seoul 06130, Korea
TEL: +82-2-501-3605, E-mail: editorial@j-mst.org |
JMST Production Office: #702 KSTC New Bldg, 22 7-gil, Teheran-ro, Gangnam-gu, Seoul 06130, Korea
TEL: +82-2-501-6056, FAX: +82-2-501-3649, E-mail: editorial@j-mst.org |
|
| |
|
|
