| |
|
|
|
|
|
|
| |
|
| |
 |
|
| |
|
|
| |
|
The Journal of Mechanical Science and Technology, Volume 22, Number 9, 2008 |
|
|
Structural optimization for a jaw using iterative Kriging metamodels
Kwon-Hee Lee
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1651-1659, 2008 |
|
|
Development and validation of FE models of impactor for pedestrian testing
Tso-Liang Teng
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1660-1667, 2008 |
|
|
Topology optimization of compressor bracket
Young Shin Lee
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1668-1676, 2008 |
|
|
Development of diagnosis system for knife and strip cutting face in the side trimming process
C. M. Suh
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1677-1683, 2008 |
|
|
Nondestructive evaluation of a crack on austenitic stainless steel using a sheet type induced current and a Hall sensor array
Jinyi Lee
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1684-1691, 2008 |
|
|
Dynamic deformation of hot temperature degraded POM and PP using a modified SHPB with pulse shaper technique
Dong Hyeok Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1692-1698, 2008 |
|
|
Magnetic circuit design by topology optimization for Lorentz force maximization in a microspeaker
Yoon Young Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1699-1706, 2008 |
|
|
Sub-workspace design of binary manipulators using active and passive joints
Yoon Young Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1707-1715, 2008 |
|
|
Random forests classifier for machine fault diagnosis
Bo-Suk Yang
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1716-1725, 2008 |
|
|
Analysis of piston behavior according to eccentricity ratio of disk in bent-axis type piston pump
Jae-Youn Jung
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1726-1733, 2008 |
|
|
Design and fabrication of a scanning electron microscope using a finite element analysis for electron optical system
Dong-Chul Han
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1734-1746, 2008 |
|
|
Effect of manufacturing tolerances on dynamic equilibria of multibody systems undergoing prescribed rotational motion
Dong Hwan Choi
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1747-1756, 2008 |
|
|
A self-sensing technology of active magnetic bearings using a phase modulation algorithm based on a high frequency voltage injection method
Dong Chul Han
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1757-1764, 2008 |
|
|
Fabrication of suspended micro-structures using diffsuser lithography on negative photoresist
Gyu Man Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1765-1771, 2008 |
|
|
Gear hot forging process robust design based on finite element method
Jung DongWon
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1772-1778, 2008 |
|
|
Lie group analysis of radiation natural convection heat transfer past an inclined porous surface
J. Lee
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1779-1784, 2008 |
|
|
Diagnosis of the behavior characteristics of the evaporative diesel spray by using images analysis
Jeongkuk Yeom
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1785-1792, 2008 |
|
|
Size distributions and number concentrations of particles from the DOC and CDPF
Byunchul Choi
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1793-1799, 2008 |
|
|
Comparison between numerical computations and measurements by LDV for fluid flow in rectangular duct systems
Kyung Hwan Kim
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1800-1807, 2008 |
|
|
A numerical study of the fluid flow and heat transfer around a single row of tubes in a channel using immerse boundary method
Changmin Son
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1808-1820, 2008 |
|
|
Investigation on hydrodynamics and mass transfer characteristics of a gas-liquid ejector using three-dimensional CFD modeling
Hanshik Chung
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1821-1829, 2008 |
|
|
Predicting the impact of vegetations in open channels with different distributaries’ operations on water surface profile using artificial neural networks
Mostafa A. M. Abdeen
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1830-1842, 2008 |
|
|
A dynamic model and numerical study on the liquid balancer used in an automatic washing machine
Chung-Hyo Jung
The Journal of Mechanical Science and Technology, vol. 22, no. 9, pp.1843-1852, 2008 |
|
|
|
|
 |
|
|
|
|
| |
| |
| |
|
|
| |
|
JMST Editorial Office: #702 KSTC New Bldg, 22 7-gil, Teheran-ro, Gangnam-gu, Seoul 06130, Korea
TEL: +82-2-501-3605, E-mail: editorial@j-mst.org |
JMST Production Office: #702 KSTC New Bldg, 22 7-gil, Teheran-ro, Gangnam-gu, Seoul 06130, Korea
TEL: +82-2-501-6056, FAX: +82-2-501-3649, E-mail: editorial@j-mst.org |
|
| |
|
|
